資訊推薦

• 【題組】193.What is the purpose of Linda Kim's email to Tracy Bishop?(A) To ask Tracy to write an a
• 【題組】194.What does Linda Kim believe will benefit the staff of the company?(A) Tracy Bishop's ex
• 【題組】195.Which of the following is NOT mentioned as an important aspect of workingcollaboratively wit
• Questions 196~200 refer to the following news, conversation, and email.TCIMM News Last month, Anders
• 【題組】197.According to the news, what is the key takeaway from this experience?(A) It is essential for
• 【題組】198.What was the main takeaway from the conversation?(A) Companies should avoid new venues.(B) V
• 【題組】199.According to the conversation, what compensation did the VP offer Mr. Anderson?(A) A full re
• 【題組】200.What is the CEO's commitment regarding the upcoming event in his email?(A) To provide a
• Questions 186~190 refer to the following email, table, and comments.Subject: Healthy Employees Day -
• 102. 如圖所示電路，若電流表 A 指示值變大，下列何種現象是正確原因？ (A)R2 被短路 (B)R2 斷路 (C)R1 斷路 (D)電源電壓 E 變小
• 2. 下列何者不是螺紋之功用？(A)鎖緊機件 (B)量測 (C)減少摩擦 (D)傳遞動力。
• 3. 若 M8 × 1 表公制 V 牙螺紋，外徑 8 mm，螺距 1 mm，則螺紋之牙深為多少 mm ?(A)0.65 (B)0.75 (C)1.3 (D)1.5。
• 4. 車床導螺桿為下列何種螺紋？(A)鋸齒形牙 (B)60°V牙 (C)方形牙 (D)梯形牙
• 5. 規格為 M20 × 1.5 × 60–1 之螺栓，下列說明何者不正確？(A)外徑 20 mm (B)螺距 1.5 mm (C)螺紋長度 60 mm (D)為公制三角形螺紋，一級配合。
• 6. 下列有關墊圈之敘述，何者最不正確？(A)螺旋彈性墊圈之斷面為圓形 (B)普通墊圈一般係以軟鋼、熟鐵或銅製成 (C)齒形墊圈具有防振之功用 (D)防止螺帽鬆脫，可使用彈簧墊圈。
• 7. 可傳遞最大扭矩的鍵是何種鍵？(A)半圓鍵 (B)栓槽鍵 (C)圓鍵 (D)方鍵。
• 8. 如圖所示，有一長 100 cm 之槓桿，利用一鍵與半徑 5 cm 之軸連結，若鍵長 4 cm，橫斷面為每邊 1 cm 之方鍵，若鍵容許剪應力為 20MPa，則作用於桿端之力量中最大為多少 N？
• 【題組】187.Which fitness program is led by a coach and incorporates a wide range of exercises toimprove
• 【題組】188.Which of the following features is shared between Yoga and CrossFit programs?(A) Both focus
• 【題組】189.What did David Perry appreciate about Sarah Tatum's Resistance Training program?(A) She
• 【題組】190.What did Zoe Magee and Simon Stone have in common in their experience with theprograms offer
• Questions 191~195 refer to the following information, web page, and comments. London's Natural
• 103. 如圖(a)(b)所示，每只電燈皆為 12V，10W，則此六只電燈之明亮程度順序為 (A)A＝B＞C＞D＞E＞F (B)C＞A＝B＞F＞D＝E (C)C＞F＞A＝B＞D＝E(D)C＞A＝B＞
• 9. 定位銷的主要功能在使兩機件：(A)使一機件能繞著定位銷在另一機件上旋轉 (B)相對的位置能夠確定 (C)夾緊在一起 (D)一塊機件在另一機件上作正確的滑動。
• 10. 螺旋壓縮彈簧的兩端磨平，其主要目的為何？(A)增加美觀 (B)減少重量 (C)增加接觸面積 (D)節省材料。